IP Unicast Routing
Static Route-configuration
\[Command] show ip route \[summary|connected|static|bgp|ospf|isis|kernel| A. B.
BGP Configuration
\[Command] show bgp peer-group \[Purpose] This command displays configured BGP peer-groups \[View] System view \[Use Cases] \[Command] show ip bgp summary \[{established|failed}] \[Purpose] View BGP neighbor information \[Parameter] \[View] System view \[Use Cases] \[Command] show ip bgp neighbors \[Purpose] Display the details of BGP neighbors \[View] System view \[Use Cases] \[Command] show ip bgp \[Purpose] Display all route information received from BGP neighbors \[View] System view \[Use Cases] \[Command] show ip bgp statistics \[Purpose] Display BGP routing-related statistics \[View] System view \[Use Cases] \[Command] router bgp AS no router bgp AS \[Purpose] Enable a BGP protocol process with the specified AS number \[Parameter] \[View] System configuration view \[Notes] When VRF VRF name is not specified, the BGP protocol process belongs to the default VRF. \[Use Cases] \[Command] bgp router-id A.
OSPF Configuration
\[Command] show ip ospf \[vrf NAME |all] \[json] \[Purpose] Display OSPF details \[View] System view \[Use Cases] \[Command] show ip ospf \[vrf NAME |all] interface \[ethernet interface name |vlan vlan id |link-aggregation lag id ] \[Purpose] Show state and configuration of OSPF the specified interface, or all interfaces if no interface is given. \[Parameter] \[View] System view \[Use Cases] \[Command] show ip ospf \[vrf NAME |all] neighbor \[ethernet interface name |vlan vlan id |link-aggregation lag id | A.
Route Map
\[Command] show route-map WORD \[Purpose] Display data about each daemons knowledge of individual route-maps \[Parameter] \[View] System view \[Use Cases] \[Command] clear route-map counters WORD \[Purpose] Clear counters that are being stored about the route-map utilization so that subsuquent show commands will indicate since the last clear \[Parameter] \[View] System view \[Use Cases] \[Command] show ip prefix-list {detail|summary| NAME } \[Purpose] Display the IP prefix list \[View] System view \[Use Cases] \[Command] bgp large-community-list {standard|expanded} NAME {permit|deny} LARGE-COMMUNITY no bgp large-community-list {standard|expanded} NAME {permit|deny} LARGE-COMMUNITY \[Purpose] This command defines a new standard large-community-list \[Parameter] \[View] System configuration view \[Notes] When filtering BGP large community attributes, you can configure multiple filter criteria within the same entry. The relationship between filter criteria is "AND," which means all filter criteria must be matched for the rule to be considered a match.
Policy Route Configuration
\[Command] show pbr interface interface-name \[Purpose] View the binding relationship between interfaces and policy routes \[View] System view \[Use Cases] \[Command] show pbr map map-name \[Purpose] Display the configured policy routes \[View] System view \[Use Cases] \[Command] show pbr nexthop-groups \[Purpose] Displays the next address group for the policy route \[View] System view \[Use Cases] \[Command] pbr-map name seq number \[Purpose] Create a policy route and enter the view \[Parameter] \[View] System configuration view \[Use Cases] \[Command] match { dst-ip ip-address|dst-port port|ip-protocol protocol|src-ip ip-address|src-port port } \[Purpose] Create match conditions for policy routing \[Parameter] \[View] Policy route view \[Use Cases] \[Command] set { nexthop ip-address|nexthop-group name } \[Purpose] Configure an action of redirecting packets to a next-hop IP address \[Parameter] \[View] Policy route view \[Notes] The redirect nexthop command allows user to specify a maximum of 4 next-hop IP addresses. If multiple next-hop IP addresses are configured, the device redirects packets in active/standby mode.
RIP configuration
\[Command] show ip rip {vrf name } \[Purpose] View the routing table of RIP routing protocol \[View] System view \[Use Cases] \[Command] show ip rip status \[Purpose] View detailed status and configuration information of RIP routing protocol \[View] System view \[Use Cases] \[Command] ip rip authentication mode \[md5|text] \[Purpose] Enable RIP packet authentication on the interface to prevent illegal routers from injecting false routes. \[Parameter] \[View] Interface Configuration View \[Use Cases] \[Command] ip rip authentication string string \[Purpose] Configure the password for RIP message authentication on the interface, which can be a plaintext password or an md5 password.
RIPng configuration
\[Command] show ipv6 ripng {vrf name } \[Purpose] View the routing table of RIPng routing protocol \[View] System view \[Use Cases] \[Command] show ipv6 ripng status \[Purpose] View detailed status and configuration information of RIPng routing protocol \[View] System view \[Use Cases] \[Command] ipv6 ripng split-horizon \[poisoned-reverse] \[Purpose] Configure horizontal cutting with RIPng enabled on the interface, and also enable both horizontal cutting and toxicity reversal simultaneously. Horizontal segmentation Do not re advertise the route from the receiving interface to prevent the router from re advertising the learned route back to the source.
VRF
\[Command] show vrf brief \[Purpose] Display vrf-related configuration information \[View] System view \[Use Cases] \[Command] vrf vrfname \[Purpose] Add VRF \[Parameter] \[View] System configuration view \[Use Cases] \[Command] ip route A. B.